Ciao a tutti sono nuovo da queste parti e poco esperto di lunx
ho un prob con la scheda kyro 2 4000xt powervr ho scaricato ed installato correttamnete i driver da http://www.powervr.com su una slakware 10.0 kernel standard 2.4. sono riuscito a settare il tutto con xorgconfig ma la primavolta che accedo da root ad x entro tranquillamente la seconda volta sempre da root si spegne il monitor. differentemente da utente normale mi dà errore. l'errore è il seguente:
Kernel requires old mod probe, but could'nt run modprobe.old: no such file or directory
(EE)POWERVR(0): couldn't obtain device info for device 1:0:0
(EE) screen (1) found, but non have a usable configuration
fatal server error:
no screen found
XIO: fatal IO error 104 on x server ":0:0)
after 0 requests (0) known processed with 0 events remaing.
per quanto riquarda la cofigurazione di xorg.conf è la seguente
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "monitor"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5 - 48.5
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-90
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
BusID "PCI:1:0:0"
Identifier "KYRO"
VendorName "STMicroelectronis "
BoardName "STG4000 [3D Prophet Kyro Series]"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
BusID "PCI:1:0:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xf86config:
Section "Device"
Identifier "Kyro driver"
Driver "powervr"
#VideoRam 65536
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "Kyro driver"
Monitor "monitor"
DefaultDepth 16
Subsection "Display"
Depth 165
Modes "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "800x600"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "800x600" "640x480"
ViewPort 0 0
EndSubsection
EndSection
i moduli caricati (ma penso che qui vada tutto bene sono) ovviamente come descritto da gigi:
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
Load "extmod"
Load "fbdevhw"
Load "record"
Load "GLcore"
Load "v4l"
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the Type1 and FreeType font modules
Load "type1"
Load "speedo"
Load "freetype"
# Load "xtt"
# This loads the GLX module
Load "glx"
# This loads the DRI module
Load "dri"
EndSection
questo per quanto riguarda l'utente invece se esco dal server x per poi rientrarci il monitor si spegne e qui non sò più cosa succede mi tocca dare cltr+alt+canc roba da winzzzzzzzz$$$
spero di essere stato chiaro
grazie in anticipo a chiunque mi volesse dare una mano ovviamente sensa impegno, io continuo a googlare nell'attesa ciao tutti
Registrazione